Your shopping cart is empty!
Eurotis CSST Piping Eurotis CSST Piping

EUROTIS CSST Pipe with a flat sealing flange is an ideal solution for heating and sanitary installations as well as industrial applications, i.e. on exchange boilers or storage tanks or connections between heaters and their storage tanks.

If you have a requirement for any number of pipe lengths finished to your specification, look here - Bespoke Production


Advantages
Low overall cost
  • quick and easy installation
  • fewer fittings needed
  • fewer repairs needed
Time saving
  • save around 66% of the time needed for a traditional installation
  • fewer connections to be made
  • spend less time checking fittings for leaks
  • bend tube into position by hand
  • install up to 50 m without needing connections
Easy Connections
  • use the same tools for all pipe types and dimensions up to DN25
  • practical electrical flange tool available for dimensions up to DN25
  • easy O-Ring connections up to DN50
  • connections created in minutes (Locking rings are not required!)
  • large selection of connectors available

Available as

 

Eurotis Edelstahlwellrohr AISI 316 L (EWG)
  • Austenitic CSST, Material No. 1.4404 to EN 10088-2, DVGW-GW354: Drinking Water 15bar Gas 100mbar
  • DN12, DN15, DN20, DN25 each in lengths of 5 m, 10 m, 25 m or 50 m

 

Eurotis Edelstahlwellrohr AISI 316 L Gas (EG)
  • as above, with 0,5 mm yellow LDPE protective coating
Eurotis Edelstahlwellrohr AISI 304 Heatline (EW)
  • Alternative for heating and solar applications. Austenitic CSST, Material No. 1.4301 to EN 10028-7
  • DN12, DN15, DN20, DN25, DN32, DN40, DN50 in lengths of 30 m or 50 m

 

Eurotis Solar Edelstahlwellrohr AISI 304 ThinPower (SW)
  • Solar twin pipe with sensor cable. Austenitic CSST, Material No. 1.4301 to EN 10028-7
  • DN15, DN20 in lengths of 25 m

Additional Notes

As long as the minimum bending radius (smallest bend radius = 2 x Pipe OD) is adhered to, the CSST Pipe may be bent from  0° to 180° in any direction. Connections and couplings should be kept to a minimum and should be easily accessable. A pipe clamp, with a plastic lining to prevent metal to metal contact (intergranular corrosion), should be fitted at approx. 0,5 m intervals. This ensures that contraction and expansion due to temperature changes will be absorbed automatically. The yellow LDPE protective coating is self-extinguishing to the requirements of the Euro-Class E.

Uncoated CSST (EW, EWG) may also be used in gas installations, ie. when replacing appliances. We recommend using the yellow coated CSST (EG) in long runs, for example through a shaft or wall. Additionally uncoated CSST (EW, EWG) and the yellow coated CSST (EG) may also be installed under floor screed. Where uncoated CSST (EW, EWG) is installed under floor screed we recommend routing it through a protective pipe. All couplings must remain easily accessable.


info    Produce a flat-sealing flange for EUROTIS CSST Pipe (EWG, EG, EW)

info    Produce an O-Ring connection for EUROTIS CSST Pipe (EWG, EG, EW)

info    How to fit the protective sleeve (EGS) to EUROTIS CSST Pipe (EG)

info    EUROTIS CSST Pipe - Sample Applications

info    EUROTIS CSST Pipe - Documents (incl. DVGW)

info    EUROTIS CSST Pipe - Multimedia

Top